The sea for several common nc machine tool nc machine tools installation and handling
From:Taian Haishu Machinery Co.,Ltd. Updatetime:2016-6-1 10:29:36 Views：
Numerical control lathe, the sea for numerical control lathe, numerical control lathe handling
The installation of nc machine tools and handling:
1, numerical control machine tool of handling: general use forklift shovel: (1) CNC lathe CK6130, CQK6136 CK6136B CNC lathe, CNC lathe, CNC lathe CAK6140, XH7130 CAK6150 numerical control lathe, machining center, CNC milling machine XK7120 generally use 3.5 tons of forklift.(2) XK714 XH7140 processing center, CNC milling machine, CNC lathe CK6163 generally use 5 tons of forklift.
2, CNC machine tool installation: when using forklift to machine tools in place, at the same time will adjust shim installation pedestal, nc machine tools installation shim can use forklift scraper lathe bed, bed cover interference, can use proper stow-wood pad between lathe bed and forklift truck.Note: forklift truck not touching the cover.
3, numerical control machine electricity: machine tool commonly used three 380 v power line (220 v), a grounded line protection, pay attention to the cable on the number of square, in the machine instruction in the circuit diagram are clearly marked.Example: the numerical control lathe CAK6150 single square root of 2.5 mm, voltage 380 v + 10%, if the voltage is too low will lead to the main shaft rotation is not stable, a sudden stop, and the cutting tool will not stop.
Note: (1) electricity before you open the electrical box, see if there are any more tripping of breakers, such as a trip the breaker closing first.2 after electricity, three-phase power source should make inspection of phase sequence, operation steps: (1) the system side key press manual - in the knife, such as motor, electric tool slide but the head did not turn, the reverse phase sequence, will any of the three phase power line two swap position.(2) or in the system according to the manual button - cooling pump, check the cooling pump is clockwise, or counterclockwise, if it is anticlockwise, the reverse phase sequence, will any of the three phase power line two swap position.
4, numerical control machine go: the head of a bed put in 32 # oil box.Headstock lubricating oil pool, generally go to the oil mark 1/3 ~ 1/2, such as oil too much will lead to headstock oil spill.
Note: (1) screw and lathe bed lubrication pump, with 46 # anti-wear hydraulic oil, must be clean, if not clean will measure a plug, screw lathe bed can't lubrication, the abrasion and belt will be particularly fast.(2) on a daily basis to check the machine when pay more attention to the X, Z to the damage of the chip board, if there are any damaged change in time, otherwise the small iron will into scraps, can lead to a lathe bed wear, scraping the crumbs board on a regular basis will also be removed cleaning, avoid iron into the scraps.This key to remind users.
5, cleaning machine: before I can start the machine tool clean rust-proof oil clean, in order to avoid the rust-proof into the screw, skateboarding, lead to machine damage, clean: after the first press get along lubrication system panel, screw first skateboard lubrication, can also be lubricating oil gun.
6, the level of the machine tool adjustment: tools generally use box type level, crowbar, stow-wood, hammer, fine iron bars.Steps: (1) level first placed in the center of the workbench, adjusted the roughly adjust shim is horizontal.(2) according to the system operation panel in manual - Z +, Z - key moving workbench, the distortion of the lathe bed set, otherwise will appear when machining cylindrical head size.
Note: the machine is in use process, such as a car cylindrical head size, value is not big, and under the premise of not crash, is can adjust the bed with the distortion to adjust.
7, the sufficient lubrication of machine tools, machine tool can be run in automatic mode
(1) machine mechanical zero back first, specific operation: press system panel in the mechanical zero point Z, X + +.(2) programming, specific operation: press system panel in the program - editor - O888 - EOB - M03 S300 (300), spindle rotation speed;M32 (lubrication pump);G0 Z - 200 (z-axis fast moving to - 200);X - 200 (X axis fast moving to - 200);G4 X4 (wait for 4 seconds);G0 X0 Z0 (fast moving to X0 Z0);G4 X4 (wait for 4 seconds);M33 (lubrication pump clearance);G99 (from a program cycle begins again), automatic reset button - - 25% - position - cycle starts, such as 10 to 20 minutes.
(3) can also press operation panel in manual - 25% - lubrication button - Z + Z, X + X -, make workbench moving back and forth, to get sufficient lubrication.
8, machine tool and coolant: be careful not to use corrosive strong cooling fluid, in the washing machine is not timely, and then parking time is too long, may be present in the machine tool bed coolant water corrosion
